Women Elegant vintage Sexy V Neck Floral Lace evening long sleeve Slim Tunic Work office Casual Party Swing Skater A Line Dress-in Dresses from Women's Clothing on AliExpress - 11.11_Double 11_Singles' Day
$ 32.83$ 20.03
|in put voltage||220v or 110v|
|Max Input Power||450w|
|Max Input Curret||5A|
90W RECI CO2 Laser Tube Power Supply
Model: HY-DY10 for W2/Z2/S2 Reci 90w Co2 Laser Tubes
Alias: Co2 Laser Generator, Co2 Laser Source,Co2 Laser Device,High Voltage Power Supply
HY-DY10 Laser Power Supply is used for 40W,50W,60W,80W Cutting and Engraving Acrylic, Fabric, Double Color Sheet and Rubber,ect.
1. Good compatibility: HY-DY10 Power Supply is specially designed for Reci 80w Laser Tubes. And it also can be applicable to 40W,50W and 60W laser tubes manufactured by other factories.
2. High Voltage Power Supply: Input AC 220V or AC 110V Voltage ,Max output DC 35KV.
3. You can choose Cutting Type or Sculpting Type; the Cutting Type has a good power stability and strong adaptability; the Sculpting Type has a quick response speed and good engraving effect. It can prolong Reci laser tubes service life.
4. This Power Supply has the” TEST” button which can test output laser manually.
1. Easy Control: The start and stop of laser can be easily controlled by TTL level.Both 0-5V analog signal and PWM signal can control the laser power.
2. The Laser Power Supply has output open circuit protection.
3. This Laser power supply has TTL signal indication, water through signal indication and laser output indication.
HY-DY10 Laser Power Supply SpecificationHY-DY10 Laser Power Supply Specification
AC220V or AC110V to be specified when placing order
Max Input Power
Max Input Curret
Max Output Voltage
Max Output Current
≥90percent full load
Mean Time Between Failure (MTBF)
≤1ms from the switch Signal is given to the output current up to 90% of the setting current
TTL level switch control; high or low effective level can be chosen (details refer to the control terminal specification)
Input-Output, Input-Shell: AC1500V 10MA 60S; Output negative is connected with machine shell.
can work in open-circuit condition for a short time Require a good protective earthing and avoid arc between the positive and the machine shell
Operating Temperature-10~40 Relative Humidity (RH)≤90percent
Force-Air Cooling (FAC)
If you need the details of the following content, please contact the online service.
Wiring diagram and terminator direction of power supply and laser
Connection diagram of power supply and control board.
The approach of exam the normality of power supply without control board.
Flow diagram of timely scene judging the laser power supply
Regular failure’s test and elimination
Power Supply Instruction
I. Instruction for sub-connection wire of the control end
1 2 3 4 5 6
5V TH TL WP G IN
1) Footer 1 is 5V power supply. (Not needed when connecting the cardinal plate. It is used when regulating
the power with potentiometer, and the 5V current should be less than 10 mA.
2) TH. TL refers to high and low power level respectively, and WP refers to water
3) Footer 5 G refers to ground, and 6 refers to input end.
4) When connecting the control plate, connect the light signal with footer2 in
5) PWM can also be used in footer 6, but the pulse peak is required to reach 5V, and the frequency should be above 20K.
6) For testing: 3, 4 and 5 are in short circuit (or 4, 5 are in short circuit and 3,
5 are connected to switch), the potentiometer center is connected with 6 IN, and
the two other ends are connected to 5V and ground (1 and 5) respectively.
7) The high power level controls the light, 1 and 2 are connected, and 4 and 5 are in
8) It is not proposed to control laser power with high
frequency modulation, because it will have impact on the service life of the
9) The model is applicable to W4 laser, it is necessary to regulate and use the
current according to the laser instructions.
II.Instruction for power wire
footer 2 footer3
AC 220V 50HZ 10A
Note: The table 10A refers to the connection wire requirement, but not the actual power dissipation.
III. Instruction for laser connection wire
1) The positive red-line with high voltage is connected to the laser tail
2) The negative white-line is connected to laser output window
IV. Current limitation
To limit the working current, the potentiometer (lies in the underside of the power supply) should be rotated in counterclockwise (please refer to the schematic diagram in our website: www.recilaser.com). Limit the maximum output current as it is regulated in the operating instruction. The working current should be limited before delivery.
V. Linear scale between input signal and the output current
Turn around the potentiometer, the linear scale will be changed: for example, when the input signal is 0-5V, the output current is 0-40mA.Or when the input signal is 0-2V, the output signal is 0-40mA.
Note: when the potentiometer is turned down too much, the real output current will be brought down by the same input signal.
VI. Using current
The use standard for our power supply is under 220V, 50Hz. The fluctuation of the input voltage and frequency will affect the working current provided by the power supply, the effection is linear relative. The unstable of the input voltage will affect the output power of the laser tube. The fluctuation of the input voltage has no effection on the lifespan of the laser if only the current provided by the power supply is not over the current limitation.
We accept bank transfer TT (Telegraphic Transfer),western union paypal etc.
Payment must be made within 48hours of the auction end time
1. we will send the goods within 3 working days once confirm your payment
2. the shipping cost does not include any import tax , and buyers are responsible for customs duties .
3.we ship mostly of the smaller order by China post Air mail (Package within 2 kg), it usually takes about 15-45 business days to arrive. The fast shipping way : if you need goods urgently , please select the faster shipping way , we can send by DHL , FEDEX , UPS , EMS and so on ,
4. If you have not received your shipment , please contact us , we will track the shipment and get back to your as soon as possible , Our goal is customer’s satisfaction ,
5. All packages by DHL fedex to brazil need to give CNPJ /CPF . All the package to Russia need the full name(first name +middle name +last name )
When you have the parcel, and not satisfied the goods or it is other problem like as broken ,please tell us the detail reason and provide the photos
Any reason required for all refund. Item must be in it's original condition and no physical damage. Buyer responsible for all shipping cost
Your satisfaction and positive feedback is very important to us ,please leave positive feedback and 5 star , if you are satisfied with our items and service .
If you have any problem with our items or service please be free to contact us first before you leave negative feedback ,we will do our best to solve any problem and provide you with the best customer service
Welcome worldwide customer inquire and question ,we will try to do our best to feedback customers by email within 1 business days.